充氣彈簧隔振器-北京市長城機床附件(河北普瑞西)

參考價	面議

充氣彈簧減振S78-11A系列

充氣彈簧減振S78-11A-05

充氣彈簧減振S78-11A-06

充氣彈簧減振S78-11A-07

類型	減震墊鐵	是否可定制	是
形狀	圓形

S78-11A-06充氣式彈簧減振墊鐵適用范圍：中小型高速壓力機及三坐座標測量?jī)x等精密設備。

詳細介紹

S78-11A-06充氣式彈簧減振墊鐵適用范圍：
中小型高速壓力機及三坐座標測量?jī)x等精密設備。
Application: Small and medium-sized high-speedpress、Coirdinate measuring machine and others precision equipments.

S78-11A-06充氣式彈簧減振墊鐵產品特點：
安裝機床不需要埋設地腳螺栓，縮短安裝周期，節省安裝費用。
根據生產工藝變化，隨意調整機床位置，實現生產流水柔性化設計。
調整機床水平方便、迅速。
自振頻率低，隔振、減振、降低噪音。
耐油性、耐腐蝕性強。
Feature of product:1.Machines are stationary on floor without anchors. Therefore the cost and time of installation can be greatly saved .2.It is convenient and quick to adjust the level of machine .3.The layout of machines can be changed freely according to the modification of manufacturing process. So it is easy to design the flexible production line .3.Vibration and nosie can be reduced and isolated by using this product.4.It can resist oil and corrosion greatly.

S78－11A系列使用方法：
How to use:
1、將機床吊起,距離地面110mm～150mm,將墊鐵放在機床下，依對角線方式由0.1 Mp、0.2 Mp…之內壓漸進方式充入氣體，直至使用內壓 0.4Mp～0.6Mp，利用輪胎內壓表檢查墊鐵內壓。
2、墊鐵使用高度為：墊鐵頂面至底板上面距離87±3mm。測試數據表明，墊鐵在該使用高度時，墊鐵的內壓、使用承載值、減振效果均達到狀態。
3、如果墊鐵較長時間不使用，可放掉墊鐵內氣體，使用時再重新充氣。
1. Lift the machine to 110-150mm high above from the ground, place the mount under the machine, and gradually pressurize it with air by 0.1Mp, 0.2Mp…, the two mounts on one diagonal should be pressurized equally, until the inner air pressure reach 0.4Mp-0.6Mp. Then check the inner pessure of the mount with a tire pressure meter.
2. The best height between the top surface and bottom of the mount is 87±3mm. Test figures shows that the inner pressure, the resisting load and the mounting effect can achieve the best situation at this height.
3.When the mount is not used for a long time, it can be deflated, and repressurized before use.

S78－11A系列安裝注意事項：
Note for installation:
1、墊鐵安裝前要先找出負荷的中心，墊鐵必須做對稱配置，按照承載值選擇適當?shù)男吞?hào)。
2、同一型號的墊鐵盡量保持同一高度。
3、在搬運過程中要輕拿輕放，以免碰壞氣門嘴，產生漏氣。
4、如需移動機床位置，必須先放掉墊鐵內的氣體，以免墊鐵中橡膠部分因內壓大而崩裂。
1. Before installation, first find out the barycentre of the load. The mounts must be symmetrically installed. Choose the suitable type according to the weight of the load.
2. Mounts of the same type should be adjusted to the same height.
3. Be careful when portage, lest the damage of the valve cause air leakage.
4．If the machine needs to be moved, deflate the mounts first, lest the rubber part blows out because of the strong inner pressure.

技術參數及選用表：

Specification and chart for choice:

型號 model	外徑（mm）	高度（mm）	螺紋（mm）	單件重量（kgs）	單件承載（kgs）	工作內壓（Mpa）	自身頻率（Hz）
S78-11A-05	300	190	M16	28.3	3000-4000	0.3-0.5	3.5-4
S78-11A-06	300	200	M16	29.5	4000-6000	0.3-0.5
S78-11A-07	300	210	M16	32	6000-8000	0.3-0.5