機床商務網
詳細介紹
進口黃銅電磁閥 Imports of brass solenoid valve
進口黃銅電磁閥工作原理：Imported brass solenoid valve works
電磁閥是用來控制流體的自動化基礎元件，屬于執行器；并不限于液壓，氣動。電磁閥用于控制液壓流動方向，工廠的機械裝置一般都由液壓鋼控制，所以就會用到電磁閥。電磁閥里有密閉的腔，在的不同位置開有通孔，每個孔都通向不同的油管，腔中間是閥，兩面是兩塊電磁鐵，哪面的磁鐵線圈通電閥體就會被吸引到哪邊，通過控制閥體的移動來檔住或漏出不同的排油的孔，而進油孔是常開的，液壓油就會進入不同的排油管，然后通過油的壓力來推動油剛的活塞，活塞又帶動活塞桿，活塞竿帶動機械裝置動。這樣通過控制電磁鐵的電流就控制了機械運動。
The solenoid valve is used to control the fluid automation infrastructure components belonging to the actuator; not limited to hydraulic, pneumatic. The solenoid valve is used to control the direction of hydraulic flow, the mechanism of the plant is generally controlled by hydraulic cylinder will be used solenoid valve. Solenoid valve has a closed cavity, in different positions with holes, each hole leading to the different tubing cavity intermediate valve, two-sided, two electromagnets, which face of the magnet coil is energized, the valve body will be attracted to which side, through the movement of the control valve member to file live or leaked oil discharge hole, and into the hole is normally open, the hydraulic oil will enter the discharge pipe, and then to push the oil through the pressure of the oil just pistons, piston driven piston rod, piston rod drive mechanism moving. So through the control solenoid current control of mechanical motion.
進口黃銅電磁閥形式種類：Imported brass solenoid valve in the form types
縱觀國內外電磁閥，到目前為止，從動作方式上可分為三大類即：直動式、反沖式、先導式，而從閥瓣結構和材料上的不同以及原理上的區別反沖式又可分為：膜片式反沖電磁閥、活塞式反沖電磁閥；先導式又可分為：先導式膜片電磁閥、先導式活塞電磁閥；從閥座及密封材料上分又可分為：軟密封電磁閥、鋼性密封電磁閥、半鋼性密封電磁閥。
Throughout the solenoid valve at home and abroad, far from the action mode can be divided into three categories: direct acting, recoil, pilot, and from the difference between the different structure and material of the valve as well as the principle of anti-red type can be divided into: a diaphragm type recoil electromagnetic valve, piston recoil solenoid valve; pilot type can be divided into: pilot operated diaphragm solenoid valve, pilot piston solenoid valve; seat and seal materials,can be divided into: soft seal solenoid valve, steel seal solenoid valve, semi-steel sealed solenoid valve.
進口黃銅電磁閥適用性：Imported brass solenoid valve applicability
性管路中的流體必須和選用的電磁閥系列型號中標定的介質*。流體的溫度必須小于選用電磁閥的標定溫度。電磁閥允許液體粘度一般在20CST以下，大于20CST應注明。工作壓差，管路zui高壓差在小于0.04MPa時應選用如直動式和分步直動式；zui低工作壓差大于0.04MPa時可選用先導式壓差式電磁閥；zui高工作壓差應小于電磁閥的zui大標定壓力；一般電磁閥都是單向工作，因此要注意是否有反壓差，如有安裝止回閥。流體清潔度不高時應在電磁閥前安裝過濾器，一般電磁閥對介質要求清潔度要好。注意流量孔徑和接管口徑；電磁閥一般只有開關兩位控制；條件允許請安裝旁路管，便于維修；有水錘現象時要定制電磁閥的開閉時間調節。注意環境溫度對電磁閥的影響電源電流和消耗功率應根據輸出容量選取，電源電壓一般允許±10%左右，必須注意交流起動時VA值較高。
Catheters in the fluid must be calibrated solenoid valve series models and optional media. The temperature of the fluid must be less than the selection of the calibration temperature of the solenoid valve. Solenoid valve to allow liquid viscosity general 20CST less than 20CST should be stated. Working pressure, maximum pressure pipeline in less than 0.04MPa should be chosen, such as direct-acting and step-by-step direct acting; minimum working pressure greater than 0.04MPa to use Pilot differential pressure solenoid valve; maximum working pressure difference should be less than the maximum calibrated pressure solenoid valve; general solenoid valves are one-way, so pay attention to the counter-pressure difference, if any, to install a check valve. Fluid cleanliness is not to be installed before the solenoid valve filter, general solenoid valve is better on media requirements cleanliness. Note flow aperture and take over the caliber; solenoid valve generally only switch two control; conditions permit to install a bypass pipe, ease of maintenance; custom solenoid valve opening and closing time to adjust to water hammer phenomenon. Note that the ambient temperature of the solenoid valve supply current and power consumption should be selected according to the output capacity of the supply voltage is generally allowed, attention must be about ± 10% AC starting value of VA is high.
工作環境溫度：-20-+40℃ -40-+80℃ Operating ambient temperature: -20 - +40 ℃ -40 - +80 ℃
線圈工作溫度： +80℃ Coil Operating Temperature: +80 ℃
控制方式：常開、常閉 Control: Normally open, normally closed
標準電壓：ＡＣ２２０Ｖ、ＤＣ２４Ｖ International standard voltage: AC220V, DC24V
流通流體介質： 水、氣、油 等 Flow of fluid medium: water, gas, oil, etc.
流通流體溫度： <+60℃、<+120℃ Circulating fluid temperature: <+60 ℃, <+120 ℃
流通流體壓力： 6bar 、10bar、16bar The circulation fluid pressure: 6bar, 10bar, 16bar
閥體材質：黃銅體 Body material: brass body
線圈連接方式：螺紋 The coil connection: thread
密封材質性能：耐溫、耐壓、耐磨、防腐 Sealing material properties: temperature, pressure, wear-resistant, anti-corrosion
密封結構：圓弧錐線與平面密封 Seal structure: conic arc with flat sealing
泄漏量：零 Leakage: Nil
性能特點：通用性廣、高靈敏性、長壽命性、嚴密性強 Performance features: wide versatility, high sensitivity, long life, strong tightness
工作范圍：水處理設備等 Scope of work: water treatment equipment
機床商務網