QCS - 3汽車內飾材料阻燃性能試驗機

五、設計標準
Five, design standards
GB8410-2006
GB8410-2006
FMVSS 571.302等標準規定的模擬燃燒性能安全試驗項目
FMVSS 571.302 standard requirements for the simulation of the combustion performance safety test project
DIN7520《汽車內飾材料的燃燒特性》
DIN7520 "combustion characteristics of automotive interior materials"
TL1010汽車內飾材料燃燒特性
Combustion characteristics of TL1010 automotive interior materials
符合標準：GM6090M、DIN75200、GM9070P、FMVSS 302、JIS D 1201、JASO M403 、ISO 3795、ASTM D5132、QB／T 2729-2005
Meet the standards: GM6090M, DIN75200, GM9070P, FMVSS 302, D JIS 1201, M403 ISO, ASTM 3795, D5132 QB, T / 2729-2005 JASO
二、汽車內飾材料阻燃性能試驗機工作條件及主要技術指標
Two, working conditions and the main technical indicators
1.環境溫度：-5℃-30 ℃
1 ambient temperature: -30 C -5 C
2.相對濕度：≤ 85%
2 relative humidity: less than 85%
3.供電電壓：220V+ 10%、50HZ,功率：100W
3 power supply voltage: 220V+ 10%, 50HZ, power: 100W
4.氣源：液化石油氣
4 gas source: liquefied petroleum gas
5.秒表精度不低于0.5s
5 stopwatch accuracy is not less than 0.5s
6.本生燈（即燃燒器）對試樣施加火焰15s
6 this lamp (i.e. burner) is applied to the test specimen with a flame 15s
7.本生燈管內徑9.5mm+ 0.1mmm，長約100mm
7 the diameter of the tube is 0.1mmm 9.5mm+, which is about 100mm
8.試驗傾角：本生燈90°垂直對著水平放置的樣品燃燒
8 test angle: the 90 degree of the lamp is placed in the vertical to the horizontal.
9.火焰高度：20mm± 2mm 到100mm±2mm可調(一般調為38mm)
9 flame height: 20mm + 2mm to 100mm + 2mm adjustable (generally adjustable to 38mm)
10.施焰時間：0-999.9s±0.1s可調（一般選擇為15s)
10 Shi Yan time: 0-999.9s + 0.1s adjustable (generally selected as 15s)
11.續燃時間：0-999.9s±0.1s，觀察火焰達到*標線后手動開始、手動暫停
11 afterflame time: 0-999.9s + 0.1s, observe the flame to the first line after the manual start, manual pause
12.燃燒氣體：液化石油氣或煤氣
12 burning gas: liquefied petroleum gas or gas
13.溫度范圍：0～200℃（顯示測試狀態下工作室內部溫度）
13 temperature range: 0 to 200 degrees C (display the test status of the studio interior temperature)
一、簡介
Brief introduction
QCS-3型試驗裝置，根據國家標準GB8410-2006《汽車內飾材料的燃燒特性》的規定技術要求而設計的，同時符合美國汽車安全技術法規FMVSS 571.302等標準規定的模擬燃燒性能安全試驗項目、德標DIN7520《汽車內飾材料的燃燒特性》及TL1010《汽車內飾材料燃燒特性》的相關要求，用于鑒別轎車、多用乘客車、載貨汽車和客車內飾材料水平燃燒特性。
QCS-3 type combustion test device of automotive interior materials, according to the national standard GB8410-2006 "automotive interior materials" the combustion characteristics of the technical requirements and design, at the same time with the American vehicle safety technical regulations FMVSS 571.302 standard combustion simulation performance security testing project, German standard DIN7520 "automotive interior materials" and "auto combustion characteristics TL1010 the combustion characteristics of" interior materials of the relevant requirements, for the identification of cars, multipurpose passenger car, truck and bus interior material level of combustion characteristics.
三、組成
Three, equipment composition
1.設備分控制部分與通風櫥一體、燃燒室內置。
1 the equipment control section and one combustion chamber, built-in ventilation cabinet.
2.點火自動控制系統
2 ignition automatic control system
3.試驗過程：試驗程序自動控制
3 test procedure: test program automatic control
4.自動進排氣系統（燃?xì)庾詣娱_啟、自動關閉）
4 automatic air intake and exhaust system (gas automatic start, automatic shutdown)
5.計時系統：燃燒計時器、余焰計時器
5 timing system: combustion timer, timer
6.U型支架：上支架有6個銷孔，下支架對應有6個銷子，并布有線徑為0.25mm及間距為25mm的耐熱金屬支撐線
6.U support: support with 6 pin holes, the lower bracket corresponding to 6 pins, and cloth cable diameter is 0.25mm and the distance to 25mm heat-resistant metal support line
7.試驗支架第三標線距第二標線距離為154mm
7 test support third from the second distance 154mm marking marking
8.耐熱金屬絲槽 0.5mm X 0.5mm 間距 25mm
8 heat resistant metal wire groove X 0.5mm 0.5mm spacing 25mm
9.金屬絲長度大于110mm,每25mm有7~8個光圓齒
9 metal wire length is greater than 110mm, each 7~8 has 25mm light round tooth
10.溫度數顯，測量范圍0-200℃
10 temperature digital display, measuring range 0-200
11.火焰標尺精度：0.1mm
11 flame scale precision: 0.1mm
12.設備外形尺寸：長 * 寬 * 高 1300 * 650 * 1200（鋼板靜電噴涂材質）
12 equipment size: long * wide * 650 * 1300 * 1200 * (steel electrostatic spraying material)
四、試樣尺寸：長356mm、寬100mm、厚≤ 13mm
Four, sample size: length 356mm, width 100mm, thickness of less than 13mm