特性

100kg… 3t, Type D1/C3/C6

1. Easy to install

2. Easy corner adjustment by matched load cell outputs

3. Full stainless steel construction

4. Wide temperature range

5. Resistant against vibration

6. Hermetically sealed, IP 68 (depth of 1.5m for 10,000 hrs.), IP 69K

7. Ex-version available

8. W& M approval (acc. to OIML R 60)

光柵式傳感器利用光柵形成的莫爾條紋把角位移轉換成光電信號（圖2）。光柵有兩塊，一為固定光柵，另一為裝在表盤軸上的移動光柵。加在承重臺上的被測物通過傳力杠桿系統使表盤軸旋轉，帶動移動光柵轉動，使莫爾條紋也隨之移動。利用光電管、轉換電路和顯示儀表，即可計算出移過的莫爾條紋數量，測出光柵轉動角的大小，從而確定和讀出被測物質量。

參數

Technical Data D1 C3 C6

Accuracy class 0.04 0.015 0.008% Emax

Minimum dead load lowest limit of specified measuring range Emin 0 0 0 % Emax

Maximum capacity highest limit of specified measuring range Emax s. table s. table s. table

Max. usable load upper limit for measurements Eu 150 150 150 % Emax

Destructive load danger of mechanical destruction Ed > 300 > 300 > 300 % Emax

Min. LC minimum load cell verification interval, (vmin= Emax/Y) Y 5,000 14,000 20,000

verification interval

Rated output relative output at nominal load Cn 2 2 2 mV/V

Tolerance on rated output permissible deviation from rated output dc < 0.25 < 0.07 < 0.07 % Cn

Zero output signal load cell output signal under unloaded condition Smin < 1.0 < 1.0 < 1.0 % Cn

Repeatability error max. change in load cell output for repeated loading εR < 0.01 < 0.005 < 0.005 % Cn

Creep, during 30 min. max. change in load cell output under nominal load dcr < 0.03 < 0.015 < 0.008% Cn

Non-Linearity max. deviation from best straight line through zero dLin < 0.03 < 0.01 < 0.01 % Cn

Hysteresis max. difference in load cell output when loading from dhy < 0.04 < 0.015 < 0.008% Cn

zero to nominal load and unloading back to zero

Temperature effect on Smin max. change of Smin/10K DT over BT referred to Cn TKSmin < 0.028 < 0.01 < 0.007 % Cn/10K

Temperature effect on C max. change of C /10K DT over BT referred to Cn TKc < 0.03 < 0.01 < 0.005 % Cn/10K

Input impedance between supply terminals RLC 650 ± 6 650 ± 6 650 ± 6

Output impedance between measuring terminals RO 610 ± 1 610 ± 0.5 610 ± 0.5 Ω

Insulation impedance between measuring circuit and housing 100VDC RIS > 5,000 > 5,000 > 5,000 MΩ

Recommended to hold the specified performance Bu 4… 24 4… 24 4… 24 V

supply voltage supply voltage

Max. supply voltage permissible for continuous operation without damage Umax 25 25 25 V

Nominal ambient to hold the specified performance BT -10… +55 -10… +55 -10… +55 ° C

temp. range

Usable ambient permissible for continuous operation without damage BTu -40… +95 -40… +95 -40… +95 ° C

temp. range

直接感受被測量(質量)并輸出與被測量有確定關系的其他量的元件。如電阻應變式稱重傳感器的彈性體，是將被測物體的質量轉變?yōu)樾巫?/span>;電容式稱重傳感器的彈性體將被測的質量轉變?yōu)槲灰?/span>。

訂貨型號

Type Nominal Load Emax Version Ex-Version Packing Weight gross/net

PR 6246/12.. 100kg /..D1 /..D1E 220 x 215 x 135mm 1.2kg/0.8kg

PR 6246/22.. 200kg /..D1/..C3/..C6 /..D1E/..C3E/C6E 220 x 215 x 135mm 1.2kg/0.8kg

PR 6246/32.. 300kg /..D1/..C3/..C6 /..D1E/..C3E/C6E 220 x 215 x 135mm 1.2kg/0.8kg

PR 6246/52.. 500kg /..D1/..C3/..C6 /..D1E/..C3E/C6E 220 x 215 x 135mm 1,2kg/0.8kg

PR 6246/13.. 1t /..D1/..C3/..C6 /..D1E/..C3E/C6E 220 x 215 x 135mm 1.9kg/0.8kg

PR 6246/23.. 2t /..D1/..C3/..C6 /..D1E/..C3E/C6E 220 x 215 x 135mm 2.1kg/1.6kg

PR 6246/33.. 3t /..D1/..C3/..C6 /..D1E/..C3E/C6E 220 x 215 x 135mm 2.1kg/1.7kg

又稱傳感元件，是將敏感元件的輸出轉變?yōu)楸阌跍y量的信號。如電阻應變式稱重傳感器的電阻應變計(或稱電阻應變片)，將彈性體的形變轉換為電阻量的變化;電容式稱重傳感器的電容器，將彈性體的位移轉變?yōu)殡娙萘康淖兓?/span>。有時某些元件兼有敏感元件和變換元件兩者的職能。如電壓式稱重傳感器的壓電材料，在外載荷的作用下，在發生變形的同時輸出電量。