描述
 CPA和CPD系列是高度可靠的CompactPCI ®系統的電源供應器。它在通信，工業，軍事，航空航天等應用越來越廣泛。該提供高功率密度符合PICMG ®電源接口規格的的CompactPCI ®系統的要求插件模塊。該轉換器采用EDGETM技術，并提供重要的優點，如靈活的輸出功率，的效率，的可靠性，完整的輸入至輸出隔離，可以忽略不計的浪涌電流，??1??76??1??77??1??76??1??77熱插拔功能，軟啟動和過熱保護。輸入是由一個瞬態抑制器（壓敏電阻）保護，防止浪涌和對源代碼行出現的瞬態和涵蓋的工作輸入電壓范圍無論從90到264 VAC或36至75 VDC 。該輸出保護，防止連續過載，開路和短路。完整的N +1冗余工作模式由集成的ORing FET的或ORing二極管成為可能。當幾個轉換器并聯連接，轉換器之間的單線連接，確保電流共享。該轉換器被設計成兩個或三個獨立的正向轉換器以固定開關頻率和同步整流器在它們的輸出。前面板和各種報警信號上的LED顯示轉換器的狀態。在鋁的情況下作為一個散熱器和一個RFI屏蔽。它是專為垂直插入19 “機架系統，但它也可以安裝在任何其他位置上，只要必要的氣流得到保證。連接器是由正電子或類似一個47針的類型。有幾個選項可用來滿足不同的要求。

特點

•RoHS無鉛焊料和無鉛焊料豁免產品可

•符合PICMG®的CompactPCI®規格

•寬范圍DC或AC輸入帶PFC

•的效率和高功率密度

•低浪涌電流

•4大電流具有靈活的負載分配輸出

•集成的ORingFET的/二極管真正的冗余

•禁止和使能輸入

•遠程檢測線

•單線電流共享功能3輸出

•熱插拔功能

•47-pin連接器，鍵入美商

•過熱，過壓，過流和過功率保護

Description

The CPA and CPD Series are highly reliable power supplies for CompactPCI® systems, which are increasingly used in communications, industrial, military, aerospace, and other applications. These power supplies offer high power density in plug-in modules that meet the requirements of the PICMG® power interface specification for CompactPCI® systems. The converters use the patented EDGETM technology and provide important advantages such as flexible output power, extremely high efficiency, excellent reliability, full input-to-output isolation, negligible inrush current, hot-swap capability, soft start, and overtemperature protection. The input is protected by a transient suppressor (varistor) against surges and transients occurring on the source lines and cover an operating input voltage range from either 90 to 264 VAC or 36 to 75 VDC. The outputs are protected against continuous overload, open-circuit, and short-circuit. Full n+1 redundant operating mode is made possible by integrated ORing FETs or ORing diodes. When several converters are connected in parallel, a single-wire connection between converters ensures current sharing. The converters are designed as two or three separate forward converters with fixed switching frequency and synchronous rectifiers at their output. LEDs on the front panel and various warning signals display the status of the converter. The aluminum case acts as a heat sink and as an RFI shield. It is designed for vertical insertion into 19" rack systems, but it can also be mounted in any other position, as long as the necessary airflow is ensured. The connector is a 47-pin type from Positronic or similar. Several options are available to meet different requirements.

Features

• RoHS lead-free-solder and lead-solder-exempted products are available

• Compliant with PICMG® CompactPCI® specifications

• Wide range DC or AC input with PFC

• Extremely high efficiency and high power density

• Low inrush current

• 4 high current outputs with flexible load distribution

• Integrated ORing FETs / diodes for true redundancy

• Inhibit and enable inputs

• Remote sense lines

• Single-wire current share function for 3 outputs

• Hot-swap capability